How To Put Harley In Transport Mode?

If you’re looking to transport your Harley, there are a few things you need to do in order to get it ready. First, you’ll want to put your bike in transport mode.

This can be done by removing the key from the ignition, disconnecting the battery, and placing the transmission in neutral. Once these steps have been completed, you can then proceed to tie down your motorcycle for transport. Doing so will ensure that your Harley arrives safely at its destination.

  • Park the motorcycle on a level surface and turn off the engine
  • Put on the parking brake and chock the wheels to prevent rolling
  • Remove any loose items from the motorcycle, such as saddlebags or luggage
  • Consult your owner’s manual for specific instructions on how to put your Harley in transport mode
  • This may involve disconnecting certain cables or removing certain parts of the bike
  • Once the bike is in transport mode, you can load it onto a trailer or into the back of a truck for transport
How To Put Harley In Transport Mode?

How Do You Turn on Harley Transport Mode?

Harley-Davidson’s transport mode is a feature that allows the motorcycle to be easily transported on a trailer or in the back of a truck. When transport mode is engaged, the motorcycle’s engine is disabled and the bike can be rolled on its side without fear of damaging the engine.

To engage transport mode, simply turn off the ignition and then press and hold the start button for five seconds. The Harley-Davidson logo will appear on the instrument cluster, indicating that transport mode is active.

How Do I Put My Motorcycle in Transport Mode?

Assuming you would like tips on how to transport your motorcycle: There are a few things to consider when transporting your motorcycle. You want to make sure the bike is secure and will not fall over while in transit. Additionally, you’ll want to avoid any potential damage to the bike by using appropriate tie-downs and straps. Here are a few tips on how to put your motorcycle in transport mode:

 1. Park the bike on a level surface and turn off the engine. Check the front wheel to prevent it from rolling.

2. loosen all of the tie-down points so that they’re just snug – don’t over-tighten as this can damage the bike’s paint job or frame.

 3. use soft loops or ratchet straps at both ends of the bike (front and rear) to secure it down; make sure that these are attached to something solid like a trailer hitch or sturdy anchor point

4. if possible, cover the entire bike with a tarp or blanket before securing it with additional straps – this will help protect it from weather conditions and debris kicked up on the road

How Do You Turn on Trailer Mode on a Harley?

If you have a Harley-Davidson motorcycle with a trailer hitch, you can easily turn on trailer mode. This will allow your bike to automatically adjust the settings for traction control, stability control, and ABS so that it is optimized for towing a trailer. Here’s how to do it:

1. Start by putting your key in the ignition and turning it to the “On” position.

2. Then, press and hold the button on your dash labeled “Mode.”

3. While continuing to hold the “Mode” button, press and release the button labeled “Trip Reset.”

4. When the message on your display reads “Trailer Mode Active,” release both buttons.

5. You’re now ready to hit the road with your trailer!

How Do I Get My Harley Out of Travel Mode?

Assuming you are talking about a Harley Davidson motorcycle: There are a few different things that you need to do in order to get your Harley out of travel mode. First, you need to find the right key.

This key is usually located on the left side of the bike, near the seat. Once you have found the key, insert it into the ignition and turn it to the “on” position. Next, locate the cluster switch on the handlebars. This switch controls all of the lights on your bike, including your headlight, taillight, and turn signals.

Flip this switch up or down until all of the lights are off. Finally, find the kill switch on your bike. This switch is usually located near the throttle grip. Push this button in and hold it for three seconds in order to deactivate travel mode.

Turn off Transport Mode Harley Davidson

If you’re like most motorcycle riders, you enjoy the wind rushing through your hair as you cruise down the open road. But there are times when you don’t want the wind in your face – like when it’s cold outside or when you’re riding in heavy traffic.

That’s where transport mode comes in. Transport mode is a feature on some Harley-Davidson motorcycles that allows you to close off the front of the bike so that the wind is redirected around and over the top of the windshield.

This can provide a more comfortable ride, especially in inclement weather. To activate transport mode, simply pull up on the lever located under your left handgrip. This will raise the windshield and seal off the front of the bike.

To deactivate the transport mode, just push down on the lever and lower the windshield back into place. So next time you’re preparing for a long ride in bad weather, be sure to take advantage of transport mode – it just might make all the difference in your comfort level!

How to Put a 2019 Harley in Transport Mode

If you’re looking to put your 2019 Harley in transport mode, there are a few things you’ll need to do. First, you’ll want to make sure that your bike is on the center stand.

Once your bike is on the center stand, you’ll want to engage the transmission by putting it in first gear. Next, you’ll want to turn off the ignition and disconnect the battery. Finally, you’ll want to tie down your motorcycle so that it doesn’t move during transport.

2022 Sportster S Transport Mode

The 2022 Sportster S Transport Mode is a unique mode of transportation that allows you to travel on both land and water.

This mode of transportation is ideal for those who enjoy the outdoors and want to explore different areas without having to worry about getting stuck in traffic or finding a place to park.

The Sportster S Transport Mode is a two-person vehicle that can reach speeds of up to 25 mph on land and 8 mph on water. This mode of transportation is perfect for exploring nature and enjoying the scenery.

Conclusion

If you’re looking to transport your Harley, there are a few things you need to do to make sure it’s ready. First, you’ll need to put the bike in transport mode.

This can be done by putting the kickstand up and engaging the parking brake. You’ll also want to make sure the handlebars are locked in place. Once the bike is in transport mode, you can strap it down using tie-downs or a motorcycle trailer.

Alston Seymour
 

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: