How To Remove Baffle From Harley Exhaust?

If you’re looking to remove the baffle from your Harley exhaust, there are a few things you’ll need to do. First, you’ll need to locate the screws that hold the baffle in place. These are typically located at the base of the exhaust where it meets the engine. Once you’ve found these screws, you’ll need to remove them with a wrench or socket set. With the screws removed, you should be able to pull the baffle out of the exhaust. Be careful when removing the baffle, as it may be hot from being near the engine.

  • First, remove the exhaust heat shield by unscrewing the bolts that hold it in place
  • Next, loosen the baffle clamp by unscrewing the bolt that holds it in place
  • After that, pull the baffle out of the exhaust pipe
  • Finally, put the heat shield back on and screw it into place
How To Remove Baffle From Harley Exhaust?

Will Removing Baffles Hurt My Harley?

The Harley-Davidson company does not recommend removing the baffles from their motorcycles.

The main reason for this is that it can cause damage to the engine. When the baffles are removed, it changes the back pressure in the exhaust system. This can cause pre-ignition, which will lead to engine knock and eventually engine failure. Additionally, removing the baffles can also void your warranty.

How Do You Remove the Baffles on a Harley Davidson?

Harley-Davidson motorcycles are known for their deep, throaty rumble. Many riders enjoy this sound, but some may find it too loud for their taste.

Luckily, Harley makes it easy to remove the baffles from most of their exhaust systems. Doing so will make your bike louder, but it’s important to be aware that you may also be violating local noise ordinances.

Before you start tinkering with your bike, it’s a good idea to check your local laws regarding motorcycle noise levels. Once you’re sure you won’t be breaking any laws, you can begin removing the baffles from your Harley’s exhaust system.

The process will vary depending on the model of bike you have but typically involves removing a few bolts and screws. If you’re not comfortable working on your own bike, or if you don’t feel confident in your ability to put everything back together correctly, it’s best to leave this job to a professional mechanic. However, if you’re up for the challenge, follow these steps and you’ll have those baffles out in no time:

1) Start by putting your bike on a lift or jack so that the rear wheel is off the ground. This will give you better access to the muffler and make it easier to work on.

2) Next, locate the bolts or screws holding the baffle in place. These are usually located around the perimeter of the baffle itself.

3) Using a socket wrench or screwdriver (depending on what type of fasteners are being used), loosen and remove all of the bolts or screws holding the baffle in place.

4) Carefully remove the baffle from inside the muffler chamber being careful not to damage anything else in there.

How Do You Take the Baffle Out of a Motorcycle Exhaust?

Assuming you would like tips on removing a baffle from a motorcycle exhaust: The first step is to identify which type of baffle is in the exhaust. There are two types of baffles- packing and perforated.

Packing baffles are made of fiberglass, metal mesh, or other materials that can be packed tightly together, while perforated baffles have small holes throughout. If the baffle is packed, it will need to be replaced once removed. To remove a packing baffle, start by unscrewing any bolts that are holding it in place.

Once the bolts are removed, the end cap can be pulled off and the packing material will fall out. If the baffle is perforated, it can be cleaned and reused. To clean a perforated baffle, start by removing any debris that may be blocking the holes.

Next, use compressed air or a power washer to blow through the holes and remove any remaining dirt or grime.

How Do I Remove the Baffles from My Vance And Hines Harley Exhaust?

If you’re looking to unleash a little more power and sound from your Vance & Hines Harley exhaust, removing the baffles is a popular way to do it.

But before you start tinkering with your exhaust, there are a few things you need to know. In this article, we’ll walk you through the process of removing the baffles from your Vance & Hines Harley exhaust, step by step.

We’ll also give you some tips on what to do (and not do) once they’re out. So why would you want to remove the baffles from your Vance & Hines Harley exhaust in the first place? Well, for starters, it will make your bike sound louder.

If you’re looking for that signature “Harley sound,” then this is a good way to get it. Additionally, removing the baffles can slightly increase power output (although this varies depending on your bike).

And finally, many riders simply find that they prefer the look of an unbaffled exhaust. Now that we’ve answered the question of “why,” let’s move on to the question of “how.” Here are step-by-step instructions for removing the baffles from your Vance & Hines Harley exhaust:

1) First things first: if your bike is still under warranty, keep in mind that removing the baffles will void it. So if that’s something that concerns you, stop here and don’t proceed any further.

2) Next, take a look at your Vance & Hines exhaust and familiarize yourself with its construction. You should see two small bolts holding each baffle in place – one near the front and one near the back. These are typically 10mm bolts (but again, it depends on your specific model).

Use a socket wrench or Allen wrench to remove these bolts (be sure to note which bolt goes where so you can put them back in correctly when reassembling). With both bolts removed, gently pull out each baffle until it comes free from the pipe. That’s all there is to it!

Removing Baffles on Fuel Injected Harley

If you’ve ever ridden a Harley with fuel injection, you know that the engine can be quite loud. One of the main reasons for this is the baffles that are installed in the exhaust system.

These baffles help to muffle the noise of the engine, but they also restrict airflow and can cause performance issues. Fortunately, there are many aftermarket options available for removing the baffles from your Harley’s exhaust system. This can be a great way to improve performance and make your bike sound more like a traditional Harley.

However, it’s important to keep in mind that removing the baffles will also make your bike louder and may not be legal in all states. If you’re interested in removing the baffles from your Harley’s exhaust, there are a few different methods you can use. The most popular method is to simply remove the bolts that hold them in place.

This can be done with a socket wrench or an impact gun. However, if you don’t have access to these tools, you can also try using a pair of pliers or vise grips. Once the bolts are removed, you should be able to pull out the baffles with your hands. If they’re stuck, you can try using a flathead screwdriver to pry them out. Once they’re out, you’ll need to install new gaskets before putting everything back together again. Installing new gaskets is critical when removing baffles from your Harley’s exhaust system because it helps prevent leaks.

There are many different types of gaskets available, so make sure you choose ones that are compatible with your particular model of motorcycle. Many aftermarket companies sell complete kits that include everything you need for installation.

Removing baffles from your fuel injected Harley’s exhaust system is relatively simple and can be done without too much difficulty. Keep in mind that this modification will make your bike louder and may not be legal in all states.

Pros And Cons of Removing Baffles

Are you thinking about removing the baffles from your motorcycle exhaust? Here are a few things to consider before taking this modification:

PROS: -Increased horsepower -Lighter weight -Better sound

CONS: -Check engine light (CEL) may come on due to increased exhaust back pressure

RCX Exhaust Baffle Removal

Removing the baffles from your RCX Exhaust will allow your motorcycle to produce more noise. This is because the baffles are designed to muffle the sound of the exhaust.

While some riders like this, others find it annoying and prefer to have a louder exhaust. If you fall into the latter category, then you’ll be happy to know that removing the baffles from your RCX Exhaust is actually quite easy.

All you need is a screwdriver and a few minutes of time. Once you have your screwdriver, simply remove the screws that hold the baffles in place. There are typically four screws, two on each side. With the screws removed, you can now pull out the baffles.

Be careful when doing this, as they can be sharp around the edges. Once the baffles are out, you’re done! Your exhaust will now be much louder than before.

Conclusion

In order to remove the baffle from a Harley exhaust, firstly, the heat shield will need to be removed. This is done by unscrewing the two bolts that hold it in place.

Once the heat shield is off, there will be four screws holding the baffle in. These screws need to be unscrewed in order to take out the baffle.

Alston Seymour
 

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: