How To Remove Harley Ignition Switch Without Key?

If you’re like most Harley-Davidson riders, you probably don’t give much thought to your ignition switch. After all, it’s just a little switch that turns on your bike, right? Wrong. The ignition switch on a Harley is actually a vital part of the motorcycle’s security system. That’s why it’s important to know how to remove it without damaging the bike or yourself.

  • Remove the screws that hold the ignition switch in place with a screwdriver
  • Pull the ignition switch out of the housing
  • Use a wire cutter to cut the wires that connect the ignition switch to the motorcycle’s electrical system
  • Tape up or otherwise secure the ends of the wires to prevent them from touching each other and causing a short circuit
How To Remove Harley Ignition Switch Without Key?

How Do You Remove an Ignition Switch Without the Key?

If your ignition switch is stuck and you don’t have a key to insert, there are a few ways you can try to remove it.

However, unless you’re an experienced mechanic, we recommend taking your car to a professional to have the switch replaced. One way to remove the ignition switch without a key is by using a screwdriver.

First, locate the two screws that hold the switch in place. Then, insert the screwdriver into each screw and turn counterclockwise until they’re both loose. Once the screws are removed, you should be able to pull out the ignition switch.

Another way to remove an ignition switch without a key is by using pliers or vice grips. First, locate the tab on the side of the switch that’s holding it in place. Then, use pliers or vice grips to grip onto the tab and pull until the switch pops out.

If neither of these methods works, your last resort would be to drill out the lock cylinder. This should only be done as a last resort because it will damage your car’s steering column. To do this, first, locate the center of the lock cylinder with a drill bit. Then, drill through the center of the cylinder until it’s completely drilled out.

How Do You Start a Harley-Davidson Without a Key?

If you’re like most Harley-Davidson riders, you probably don’t give much thought to how you start your motorcycle.

After all, as long as the key is in the ignition and the engine turns over, that’s all that matters, right? Wrong. Believe it or not, there is a right way and a wrong way to start a Harley-Davidson motorcycle.

And if you’re not doing it the right way, you could be causing unnecessary wear and tear on your engine – and shorten its lifespan in the process. So what’s the right way to start a Harley? It’s actually pretty simple:

1) Make sure the gas tank is turned on. This may seem like an obvious step, but it’s one that many riders forget. If the gas tank is off, your engine isn’t going to get the fuel it needs to run properly.

2) Prime the carburetor by turning on the choke (if your bike has one). This will help ensure that enough fuel gets into the combustion chamber when you first start up your engine.

How Do I Remove an Ignition Switch?

Assuming you would like to know how to remove an ignition switch from a vehicle, the process will vary depending on the make and model of the vehicle.

In general, however, there are a few steps that are typically followed. First, the negative battery terminal should be disconnected to prevent any electrical shorts. Next, locate the ignition switch. It is usually mounted on or near the steering column. Once found, disconnect any wiring harnesses or plugs that are attached to it.

Some switches may also be held in place by a retaining clip or screw; if so, remove this as well. With all fasteners removed, the switch can now be pulled out and replaced with a new one. Be sure to reconnect all wiring and plugs before reattaching the battery terminal.

How Do You Remove the Ignition Switch on a 2013 Harley-Davidson?

Assuming you need to replace the ignition switch on your 2013 Harley-Davidson: To remove the ignition switch, you will first need to disconnect the battery.

Next, locate the three screws that hold the Ignition Switch Housing Cover in place and remove them. With the cover removed, you will be able to see the back of the ignition switch.

There are two electrical connectors that need to be disconnected before removing the final two screws holding the ignition switch in place. Once those are removed, simply pull out the old ignition switch and insert the new one.

Make sure all connections are secure and reattach your Ignition Switch Housing Cover before reconnecting your battery.

Harley Ignition Switch Cover Removal

If you’re like most Harley riders, you probably don’t give your ignition switch cover much thought. But if it’s time to replace yours, or you just want to clean it up a bit, you’ll need to know how to remove it.

Luckily, this is a pretty easy process that anyone can do. First, you’ll need to locate the two screws that hold the cover in place. These are usually located on the back side of the cover. Once you’ve found them, use a screwdriver to remove them. Next, gently pry the cover off of the ignition switch itself.

Be careful not to damage either piece as you do this. Once the cover is removed, you’ll be able to access the ignition switch itself and any other components that may need cleaning or replacing. When you’re finished with your repairs or maintenance, simply reverse the process and reattach the cover.

Harley Toggle Ignition Switch

If you’re a Harley rider, then you know the importance of having a good toggle ignition switch. After all, this is what turns your bike on and off! But what exactly is a toggle ignition switch?

A toggle ignition switch is a type of switch that is used to control the electrical system on a motorcycle. It is usually located on the handlebars near the right-hand grip.

The switch has two positions: “on” and “off”. When the switch is in the “on” position, it completes the circuit between the battery and the spark plugs, allowing the engine to start. When the switch is in the “off” position, it breaks the circuit and prevents the engine from starting.

There are several reasons why you might want to upgrade your toggle ignition switch. Perhaps you’re not happy with the quality of your current one, or maybe you want something that looks nicer or functions better. Whatever your reason, we’ve got plenty of options for you to choose from. Take a look at our selection of toggle ignition switches and find one that’s perfect for your Harley!

Harley Ignition Switch Problems

If you own a Harley, you may have experienced ignition switch problems. Ignition switches on Harleys are located on the right side of the handlebar and are used to turn the bike on and off.

Over time, these switches can wear out, causing them to become stuck in the “on” position or become difficult to turn. When this happens, it’s important to replace the switch as soon as possible to avoid further damage to your bike.

There are a few signs that your Harley’s ignition switch is starting to fail. If you notice that your engine is hard to start or if the key feels like it’s getting stuck when you try to turn it, these could be early indications of a problem.

In some cases, the key may even get stuck in the “on” position, preventing you from being able to turn the engine off. If you experience any of these issues, it’s best to take your bike to a qualified mechanic for service. Replacing an ignition switch on a Harley is relatively simple and can be done with just a few tools.

However, if you’re not comfortable working on your own bike, it’s always best to leave this type of repair to a professional. With their help, you can ensure that your Harley will be back up and running in no time!

Conclusion

If you’re looking to remove your Harley ignition switch without a key, there are a few things you’ll need to do.

First, locate the switch on the bike – it’s usually located near the fork area. Once you’ve found it, use a small screwdriver or other tools to pry off the retaining clip that holds the switch in place.

With the clip removed, you should be able to pull the switch out of its housing. Next, take a look at the wiring harness that connects to the back of the ignition switch. You’ll need to disconnect this so that you can remove the entire assembly from the bike.

To do this, simply unplug the connector from the back of the switch and then pull it through until it’s free. Now that everything is disconnected, you can remove your Harley ignition switch without a key!

Alston Seymour
 

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: